Jump to content


Photo

1-perf issue with Bolex H16 Leader

1R bolex transport

  • Please log in to reply
4 replies to this topic

#1 Gabi Bucataru

Gabi Bucataru
  • Basic Members
  • PipPip
  • 10 posts
  • Cinematographer
  • Chicago, USA

Posted 08 September 2016 - 09:25 AM

Hi everyone!

New guy on the block with a Bolex H16 Leader issue I have with single perforation films. Eager to try out this camera, (off ebay), I got two 100' rolls of Kodak VISION3 50D #7203 (single perforation film), loaded them and shot them all at 24 fps.
Things sounds good in the camera, I was careful to have a good exposure using my sekonic light meter, etc.
But when the rolls returned from the lab, surprise, surprise... Out of two rolls I only got this footage (the rest of the rolls look like what can be seen from 00.40 onward):


I did a cold check of how film runs through the camera and I discovered that there are no issues with 2-perf film. However, the Bolex H-16 doesn't seem to favor single perforation film, and the lower sprocket tends to push it off and tighten the loops. From there the film runs but the tight loops will mess the smooth transport and get the result shown in the example movie.

Here's a shot I took of how the camera transports double and single perforation film. Please ignore the non-behaving receiving roll -- it's the only one I had on hand, an older type that was slightly bigger than the usual ones and was catching a little.



So the question I have -- since single-perf film are the most you can find on the market today, do I have any hope to fix this issue?

thanks a lot,
Gabi


  • 0

#2 Robert Ditto

Robert Ditto
  • Sustaining Members
  • 72 posts
  • Other

Posted 08 September 2016 - 10:25 AM

Are your camera's sprockets single perf or double perf?

Attached Images

  • 2016-09-08_10.22.28.jpg

  • 1

#3 Gabi Bucataru

Gabi Bucataru
  • Basic Members
  • PipPip
  • 10 posts
  • Cinematographer
  • Chicago, USA

Posted 08 September 2016 - 10:27 AM

Are your camera's sprockets single perf or double perf?

Thanks Robert!

 

They are double perfs. :-(


  • 0

#4 Tyler Purcell

Tyler Purcell
  • Sustaining Members
  • 4274 posts
  • Other
  • Los Angeles

Posted 08 September 2016 - 12:16 PM

Yea, I'd say that's your issue! A lot of those inexpensive H16's are double perf, that's why they're so cheap.
  • 0

#5 Gabi Bucataru

Gabi Bucataru
  • Basic Members
  • PipPip
  • 10 posts
  • Cinematographer
  • Chicago, USA

Posted 08 September 2016 - 12:47 PM

Yea, I'd say that's your issue! A lot of those inexpensive H16's are double perf, that's why they're so cheap.

Thanks Tyler.

 

Yes - from what I am reading Bolex started making single tooth sprockets starting 1952 (after serial 76,471).

thanks!


  • 0



Tai Audio

FJS International, LLC

Abel Cine

Media Blackout - Custom Cables and AKS

CineLab

Willys Widgets

Gamma Ray Digital Inc

Broadcast Solutions Inc

Ritter Battery

New Pro Video - New and Used Equipment

Wooden Camera

The Slider

Visual Products

Aerial Filmworks

CineTape

rebotnix Technologies

Glidecam

Paralinx LLC

Metropolis Post

Rig Wheels Passport

Technodolly

Tai Audio

Media Blackout - Custom Cables and AKS

Visual Products

The Slider

Aerial Filmworks

Abel Cine

Willys Widgets

CineLab

rebotnix Technologies

Wooden Camera

Technodolly

Paralinx LLC

Metropolis Post

Ritter Battery

Rig Wheels Passport

Broadcast Solutions Inc

Gamma Ray Digital Inc

CineTape

New Pro Video - New and Used Equipment

FJS International, LLC

Glidecam