Jump to content


Photo

Kinor 16 run time


  • Please log in to reply
2 replies to this topic

#1 Tristin Deveau

Tristin Deveau

    New

  • Basic Members
  • Pip
  • 9 posts
  • Student

Posted 14 September 2006 - 11:27 PM

I've been looking into the Kinor 16 SX-2M a little bit, and I keep running into a 'maximum run time' field in the description, being listed at 10 minutes. Is this just talking about the fact that the maximum mag size if 400', which is about 10min. in 24fps, or does this refer to something else?
  • 0

#2 Scott Bullock

Scott Bullock
  • Basic Members
  • PipPipPip
  • 245 posts
  • Other
  • Denver, CO

Posted 15 September 2006 - 12:08 AM

It just refers to the running time of one 400' roll of 16mm film, which is what 1 magazine will hold. You can strap as many 400' mags as you want to that camera, one right after the other.
  • 0

#3 Olex Kalynychenko

Olex Kalynychenko
  • Basic Members
  • PipPipPipPip
  • 868 posts
  • Cinematographer
  • Dnepropetrovsk, Ukraine

Posted 15 September 2006 - 11:44 AM

I've been looking into the Kinor 16 SX-2M a little bit, and I keep running into a 'maximum run time' field in the description, being listed at 10 minutes. Is this just talking about the fact that the maximum mag size if 400', which is about 10min. in 24fps, or does this refer to something else?


The original user manual of Kinor-16 camera ( 16CX-2M.00.000 TO) Show :
"greatly possible time unceasing film shooting - 10 minutes ".

I think, this is the running time of one 400 magazine at speed 25 fps.

I make a some test with run of 4 pcs of 120 m film magazines with pause for connect next magazine.
After, i open a lid of motor, check temperature of electronic parts, to open a front part of body and check temperature of base parts of mechanism.
I can tell, i not see increase of temperature too much.
All parts have " normal " temperature and i think, the parts of Kinor have very good cooling.
I check of operating current of electrical motor for all magazines and not see change too much too.
This is confirm of idea, what mechanism not lost oil and not change a resistance of rotation.

The original user manual to show information about service.
You need set 2-3 drops of oil on oil channel ( red points near film gate ) and base axis of mirror disk ( hole inside screw of mirror disk ) not less one times at month.
After service, need run camera at speed 25 fps 10-15 sec.
The detailed service and outside inspection need do not less one time at 3 months and after run 10000 m of film.
  • 0


Ritter Battery

CineTape

rebotnix Technologies

Visual Products

Gamma Ray Digital Inc

FJS International, LLC

Rig Wheels Passport

Technodolly

Broadcast Solutions Inc

Willys Widgets

Tai Audio

CineLab

The Slider

Paralinx LLC

Media Blackout - Custom Cables and AKS

Aerial Filmworks

Glidecam

Abel Cine

Wooden Camera

Metropolis Post

New Pro Video - New and Used Equipment

CineTape

Glidecam

Wooden Camera

rebotnix Technologies

Paralinx LLC

The Slider

Gamma Ray Digital Inc

Visual Products

Willys Widgets

CineLab

Aerial Filmworks

Abel Cine

FJS International, LLC

Tai Audio

Rig Wheels Passport

New Pro Video - New and Used Equipment

Technodolly

Broadcast Solutions Inc

Metropolis Post

Media Blackout - Custom Cables and AKS

Ritter Battery