Jump to content


Photo

Please help


  • Please log in to reply
4 replies to this topic

#1 Nick Norton

Nick Norton
  • Basic Members
  • PipPipPip
  • 248 posts
  • Student
  • Chicago

Posted 15 October 2008 - 10:04 AM

So, while shooting the other day my Eclair ACL motor suddenly stopped running. The green light would still turn on when the camera was turned on, but nothing would happen when i tried to run the motor.


I figured my battery had run out (hadn't needed to recharge it yet since i got it) and waited the long 16 hours for the battery to charge.


However, after charging the battery the camera will turn on, but when i try to run the motor it runs but it is not up to speed and you can hear a strange clicking sound. This is when the dreaded red light begins to blink on the side of the camera. Tried another magazine, so it isn't a film jam. Perhaps i recharged the battery incorrectly and need a new one?


Any help would be appreciated!

Thanks-
nicholas
  • 0

#2 Adrian Sierkowski

Adrian Sierkowski
  • Sustaining Members
  • 7373 posts
  • Cinematographer
  • Los Angeles, Ca

Posted 15 October 2008 - 11:27 AM

Sounds like a motor issue to me moreso than a battery issue. See if you can find an eclair tech to give it a look give
http://www.visualpro...a...D=85&Cat=84

a try. Good people. I buy most of my used equipment from them. Never had an issue.
  • 0

#3 Chris Squires

Chris Squires

    New

  • Basic Members
  • Pip
  • 1 posts
  • Camera Operator

Posted 15 February 2009 - 03:17 PM

So, while shooting the other day my Eclair ACL motor suddenly stopped running. The green light would still turn on when the camera was turned on, but nothing would happen when i tried to run the motor.


I figured my battery had run out (hadn't needed to recharge it yet since i got it) and waited the long 16 hours for the battery to charge.


However, after charging the battery the camera will turn on, but when i try to run the motor it runs but it is not up to speed and you can hear a strange clicking sound. This is when the dreaded red light begins to blink on the side of the camera. Tried another magazine, so it isn't a film jam. Perhaps i recharged the battery incorrectly and need a new one?


Any help would be appreciated!

Thanks-
nicholas

I would send your motor to AZ Spectrum in New York. That is where Visual Products sends their ACL motor repairs. He knows more about those motors than anyone else.
  • 0

#4 Boris Belay

Boris Belay
  • Basic Members
  • PipPipPip
  • 210 posts
  • Other
  • Brussels, Belgium

Posted 16 February 2009 - 06:44 AM

Hi Nicolas,

It sounds like you may have a motor problem indeed. But don't worry about the red light -- it SHOULD be blinking when the camera is running.

The logic may not be evident but the diodes on the side of the ergo handgrip adapter (originally on late models ACLs) worl like this : the green diode is on when there is power to the camera (lightmeter on and motor ready) and the the red diode blinks when the camera is running. There is no fault indicator on any ACLs besides the out-of-synch light on the top of the motor.

Did you try running the camera without a magazine ? If the motor runs up to speed, you may just have a weak battery.
Did you try the other speeds on the motor? (Try the slow speeds first!)
What more can you tell us about the clicking sound ? Where does it come from : the motor, the camera, or the mag?

B.

So, while shooting the other day my Eclair ACL motor suddenly stopped running. The green light would still turn on when the camera was turned on, but nothing would happen when i tried to run the motor.


I figured my battery had run out (hadn't needed to recharge it yet since i got it) and waited the long 16 hours for the battery to charge.


However, after charging the battery the camera will turn on, but when i try to run the motor it runs but it is not up to speed and you can hear a strange clicking sound. This is when the dreaded red light begins to blink on the side of the camera. Tried another magazine, so it isn't a film jam. Perhaps i recharged the battery incorrectly and need a new one?


Any help would be appreciated!

Thanks-
nicholas


  • 0

#5 Nick Norton

Nick Norton
  • Basic Members
  • PipPipPip
  • 248 posts
  • Student
  • Chicago

Posted 16 February 2009 - 11:48 AM

Thanks for all the help.

After sending the cam to Bernie at Super16inc, it's back and working "like a motherf*cker." (To quote Bernie)

If anyone needs any more good words to acquire confidence in Bernie, consider it done. Camera works great and is REAL quiet.


-Nick
  • 0


Glidecam

Metropolis Post

New Pro Video - New and Used Equipment

Broadcast Solutions Inc

Visual Products

CineLab

Paralinx LLC

Tai Audio

Wooden Camera

Abel Cine

Technodolly

rebotnix Technologies

Aerial Filmworks

Rig Wheels Passport

Ritter Battery

FJS International, LLC

Media Blackout - Custom Cables and AKS

The Slider

Gamma Ray Digital Inc

Willys Widgets

CineTape

Broadcast Solutions Inc

Metropolis Post

Rig Wheels Passport

Wooden Camera

Glidecam

Tai Audio

Gamma Ray Digital Inc

FJS International, LLC

CineTape

Media Blackout - Custom Cables and AKS

New Pro Video - New and Used Equipment

rebotnix Technologies

Visual Products

Willys Widgets

Technodolly

CineLab

Abel Cine

Paralinx LLC

The Slider

Ritter Battery

Aerial Filmworks