Jump to content


Photo

Krasnogorsk-3 spring winder piece came off

Krasnogorsk-3 spring

  • Please log in to reply
6 replies to this topic

#1 Bernhard Kipperer

Bernhard Kipperer
  • Basic Members
  • PipPip
  • 17 posts
  • Other
  • Graz, Austria

Posted 12 January 2017 - 03:04 PM

Hi all!

 

The spring winder piece on my recently bought Krasnogorsk-3 just came off the body, see the attached image that shows it.

 

Any idea how I could get that back onto it, I can't believe that would be my second body already to break within a few weeks after purchasing (on the first one the spring itself broke inside).

 

Bernhard

Attached Images

  • k3spring.jpg

  • 0


Support Cinematography.com and buy gear using our Amazon links!
PANASONIC LUMIX GH5 Body 4K Mirrorless Camera, 20.3 Megapixels, Dual I.S. 2.0, 4K 422 10-bit, Full Size HDMI Out, 3 Inch Touch LCD, DC-GH5KBODY (USA Black)

#2 Bernhard Kipperer

Bernhard Kipperer
  • Basic Members
  • PipPip
  • 17 posts
  • Other
  • Graz, Austria

Posted 13 January 2017 - 06:29 AM

I was able to push the lever thingy (marked red above) back onto the the body.

The teeth of the lever go into two holes in the thing marked blue above.

 

I can wind again if I do it carefully, the problem is that it can come off any time again as this is very loose, see below image.

Any idea how I can tighten this? Maybe the two holes on top of the thing marked blue??

 

Bernhard

 

Attached Images

  • lever.jpg

  • 0

#3 aapo lettinen

aapo lettinen
  • Basic Members
  • PipPipPipPip
  • 869 posts
  • Other
  • Finland

Posted 13 January 2017 - 07:22 AM

1. remove that small center screw which has two holes, you may need a suitable tool for it 

 

2. remove the plate and washer 

 

3. now you see the grooves where the latch is attached and you can remove the latch 

 

4. fine tune the latch to fit perfectly to the grooves 

 

5. reattach latch 

 

6. reattach the washer, plate and screw 

 

I may have a picture here somewhere...


  • 0

#4 Bernhard Kipperer

Bernhard Kipperer
  • Basic Members
  • PipPip
  • 17 posts
  • Other
  • Graz, Austria

Posted 13 January 2017 - 08:15 AM

Thanks a lot, I will try to follow your steps.

And yes, if you could find any picture that illustrates the steps, please share with me.

 

Bernhard


  • 0

#5 aapo lettinen

aapo lettinen
  • Basic Members
  • PipPipPipPip
  • 869 posts
  • Other
  • Finland

Posted 13 January 2017 - 09:39 AM

here's a picture what is under the 2hole screw: 

 

32135303472_a40fbcff5d_c.jpg

 

the whole procedure should take only couple of minutes  ^_^


  • 0

#6 aapo lettinen

aapo lettinen
  • Basic Members
  • PipPipPipPip
  • 869 posts
  • Other
  • Finland

Posted 13 January 2017 - 09:43 AM

if the screw is loose from the beginning you can first try to tighten it. if that resolves the problem you don't have to go any further


  • 0

#7 Bernhard Kipperer

Bernhard Kipperer
  • Basic Members
  • PipPip
  • 17 posts
  • Other
  • Graz, Austria

Posted 13 January 2017 - 10:27 AM

Thank you so much for your great advice.

This only took me a minute and all seems fine again now!

 

Bernhard


  • 0



Rig Wheels Passport

Quantum Music Works

Willys Widgets

Gamma Ray Digital Inc

FJS International, LLC

Metropolis Post

Ritter Battery

Tai Audio

CineLab

The Slider

Aerial Filmworks

Broadcast Solutions Inc

Pro 8mm

CineTape

Media Blackout - Custom Cables and AKS

Glidecam

rebotnix Technologies

Visual Products

Paralinx LLC

ZoomCrane

Technodolly

Abel Cine

Metropolis Post

Paralinx LLC

Abel Cine

The Slider

rebotnix Technologies

Tai Audio

ZoomCrane

Technodolly

Visual Products

CineTape

Aerial Filmworks

Quantum Music Works

Glidecam

Willys Widgets

Gamma Ray Digital Inc

CineLab

Rig Wheels Passport

Pro 8mm

Media Blackout - Custom Cables and AKS

Ritter Battery

FJS International, LLC

Broadcast Solutions Inc