Jump to content


Photo

Sensor to Flange distance of URSA Mini PL


  • Please log in to reply
3 replies to this topic

#1 Tom Visser

Tom Visser
  • Basic Members
  • PipPip
  • 20 posts
  • Sound Department
  • Hawaii

Posted 08 February 2018 - 03:41 AM

Can anyone tell me what the flange distance is for the URSA Mini PL (not the Mini PRO - unless they happen to have the same distance - highly probably I guess)?  Specifically, the distance from the sensor to the face when you remove the PL mount.  Why?  I'm trying to fabricate a custom adapter that happens to use the B4 adapter, but I suspect that with the optics in there, its not simply the standard 48mm of the typical B4 flange distance.

 

blackmagic_design_cinecamursamtb4_b4_lens_mount_for_1496078415000_1186264.jpg


  • 0

#2 Phil Rhodes

Phil Rhodes
  • Sustaining Members
  • 12298 posts
  • Other

Posted 08 February 2018 - 05:08 AM

For that you'd need to get hold of a camera and measure it. There isn't, as far as I know, any standard involved in a bit of custom design like that.


  • 0

#3 Dom Jaeger

Dom Jaeger
  • Basic Members
  • PipPipPipPip
  • 1809 posts
  • Other
  • Melbourne, Australia

Posted 08 February 2018 - 05:54 AM

You'd want to measure the PL mount from flange to seat and subtract that figure from 52.00mm to get the optical depth from seat to sensor. It's very hard to measure to the actual sensor since it will have a protective cover glass. (But no OLPF with Ursa Mini I think?)

Given that flange depth tolerances are around 0.01mm, the final shimming is best done with a test lens that is accurately collimated.
  • 0

#4 Tom Visser

Tom Visser
  • Basic Members
  • PipPip
  • 20 posts
  • Sound Department
  • Hawaii

Posted 08 February 2018 - 06:14 AM

You'd want to measure the PL mount from flange to seat and subtract that figure from 52.00mm to get the optical depth from seat to sensor. It's very hard to measure to the actual sensor since it will have a protective cover glass. (But no OLPF with Ursa Mini I think?)

Given that flange depth tolerances are around 0.01mm, the final shimming is best done with a test lens that is accurately collimated.

 

That's more or less the plan, get close as possible (hopefully undercutting a bit) with the first machined part - assemble the front and rear mounts, then shim until it tests spot on with the lens, then machine the final part maybe 0.5mm undercut so I can have 1 shim in place in case I need room to adjust either way in the future.


  • 0


CineTape

Technodolly

Metropolis Post

Glidecam

Media Blackout - Custom Cables and AKS

Willys Widgets

Broadcast Solutions Inc

Aerial Filmworks

Abel Cine

Ritter Battery

New Pro Video - New and Used Equipment

Rig Wheels Passport

rebotnix Technologies

Tai Audio

The Slider

Paralinx LLC

CineLab

Gamma Ray Digital Inc

FJS International, LLC

Wooden Camera

Visual Products

Wooden Camera

Glidecam

Tai Audio

Technodolly

Metropolis Post

Media Blackout - Custom Cables and AKS

Gamma Ray Digital Inc

Willys Widgets

Broadcast Solutions Inc

Ritter Battery

CineLab

rebotnix Technologies

Paralinx LLC

FJS International, LLC

Abel Cine

New Pro Video - New and Used Equipment

Visual Products

The Slider

Aerial Filmworks

CineTape

Rig Wheels Passport